Items Needed:

---

Caution:

• Never apply this update data to any product other than the VRC-01. This update data may destroy the data or system program of other products.
  
  
• Never power-off your VR-1HD while the update is in progress!
  If a power failure or similar accident occurs during the update process, the VRC-01 won’t be able to start up in normal operating mode. This will require servicing, so you will need to contact Roland service center near you if this occurs.

---

Procedure:

Step 1

Download the System Program Firmware update file from the AeroCaster Downloads Page.

Scroll to the bottom of the page, click the checkbox, and click on the orange button to download.

 

It will appear in your downloads folder as vrc01_sys_v107.zip.

Note: The latest version is "vrc01_sys_v107.zip", this image is for reference

 

The update file will be contained in the downloaded .ZIP archive file. You will need to extract the .BIN file inside the .ZIP file, and save it for later.

Note: The latest version is "vrc01_sys_v107", this image is for reference

 

Do not open the .BIN file, it is not a program that runs on your computer, and do not rename it. You will later transfer it to the VRC-01 in the following steps.

 

Step 2

Hold down both the ASSIGNABLE DECK [1] (LOW CUT) and SCENE [1] (PinP 1) buttons at the same time and connect a USB 2.0 or 3.0 cable between the DEVICE port on the back of the VRC-01 and the computer.

 

When looking at the back panel, DEVICE is the 2nd USB-C port on the right.

 

Do not connect the 5V DC IN port to a USB power supply, only the DEVICE port should be connected.

 

Continue holding down the buttons until only the ASSIGNABLE DECK [1] (LOW CUT) button repeatedly flashes RED.

 

Step 3

The VRC-01 will appear on the computer as a removable drive called "USB Drive".

Open the "UPD" folder on that removable drive.

• Windows: Within My Computer (or Computer), open "USB Drive" (or Removable Disk).
• Mac: In Finder or on the Desktop, open the "USB Drive" icon.

 

Step 4

Copy and paste (or drag and drop) the "VRC_upd.bin" file from the "vrc01_sys_v107" folder to the "UPD" folder of the VRC-01 "USB Drive".

Do not copy any folders, the .BIN file should be the only file in the "UPD" folder.

 

Step 5

After the copy has been completed, safely remove the VRC-01 "USB Drive" on your computer to begin the update.

• Windows: Right-click on the "USB Drive" icon in My Computer (or the "Removable Disk (*:)" icon) and click "Eject."
• Mac: Drag the "USB Drive" icon to the Trash icon in the Dock.

Do not unplug or power off the VRC-01 yet, you need to leave it powered on until the update is complete.

• The update takes about 2 minutes to complete.

 

Step 6

During the update, the SCENE [1] (PinP 1) button will flash RED.

 

When both the ASSIGNABLE DECK [1] (LOW CUT) and SCENE [1] (PinP 1) buttons are lit solid RED, the update is finished.

• If both buttons are blinking RED, please try the update again.

 

Step 7

Unplug the USB cable from the DEVICE port, wait 5 seconds, and connect it again.

The update is complete, and you can connect the VRC-01 to your iPad again.

 

Step 8

Optional: To verify the VRC-01 version number, first disconnect the USB cable from its DEVICE port.

Hold down the VIDEO SELECT [4] and ASSIGNABLE DECK [6] (SE 2) buttons and connect the USB cable to the DEVICE port.

 

The buttons that are lit solid RED indicate the version number, based on the row it is on.

For example, let's see what version 1.07 would look like, expressed as "XYZ":

• X = VIDEO SELECT [1] through [4]
• Y = SCENE [1] through [4]
• Z = ASSIGNABLE DECK [4] through [6] and [USER]

For version 1.07 the following buttons are lit:

• VIDEO SELECT [4]
• ASSIGNABLE DECK [5] (SE 1)
• ASSIGNABLE DECK [6] (SE 2)
• ASSIGNABLE DECK [USER]

Based on the below chart, here's why:

• VIDEO SELECT [4] means "1" because that's the only lit button on that row.
• No Scene buttons are lit, so that means "0".
• ASSIGNABLE DECK [5](SE 1), ASSIGNABLE DECK [6](SE 2), and ASSIGNABLE DECK [USER] lit mean "7".

Once you are finished, you can unplug the VRC-01 and connect it to your iPad again.

No.	LED Decoder Chart
	VIDEO SELECT [1]	VIDEO SELECT [2]	VIDEO SELECT [3]	VIDEO SELECT [4]
	SCENE [1]	SCENE [2]	SCENE [3]	SCENE [4]
	DECK [4]	DECK [5]	DECK [6]	[USER]
0	Unlit	Unlit	Unlit	Unlit
1	Unlit	Unlit	Unlit	Lit RED
2	Unlit	Unlit	Lit RED	Unlit
3	Unlit	Unlit	Lit RED	Lit RED
4	Unlit	Lit RED	Unlit	Unlit
5	Unlit	Lit RED	Unlit	Lit RED
6	Unlit	Lit RED	Lit RED	Unlit
7	Unlit	Lit RED	Lit RED	Lit RED
8	Lit RED	Unlit	Unlit	Unlit
9	Lit RED	Unlit	Unlit	Lit RED

 

More Information

For more information about VRC-01 Firmware, refer to the System Program link on the Downloads page.

Note: This is separate from the manuals.